ScyllaDB Docs ScyllaDB Open Source ScyllaDB for Administrators Procedures Cluster Management Procedures Replace a Dead Node in a ScyllaDB Cluster

Caution

You're viewing documentation for a previous version. Switch to the latest stable version.

Replace a Dead Node in a ScyllaDB Cluster¶

Replace dead node operation will cause the other nodes in the cluster to stream data to the node that was replaced. This operation can take some time (depending on the data size and network bandwidth).

This procedure is for replacing one dead node. To replace more than one dead node, run the full procedure to completion one node at a time.

Prerequisites¶

Verify the status of the node using nodetool status command, the node with status DN is down and need to be replaced

Datacenter: DC1
Status=Up/Down
State=Normal/Leaving/Joining/Moving
--  Address        Load       Tokens  Owns (effective)                         Host ID         Rack
UN  192.168.1.201  112.82 KB  256     32.7%             8d5ed9f4-7764-4dbd-bad8-43fddce94b7c   B1
UN  192.168.1.202  91.11 KB   256     32.9%             125ed9f4-7777-1dbn-mac8-43fddce9123e   B1
DN  192.168.1.203  124.42 KB  256     32.6%             675ed9f4-6564-6dbd-can8-43fddce952gy   B1

Warning

It’s essential to ensure the replaced (dead) node will never come back to the cluster, which might lead to a split-brain situation. Remove the replaced (dead) node from the cluster network or VPC.

sudo rm -rf /var/lib/scylla/data
sudo find /var/lib/scylla/commitlog -type f -delete
sudo find /var/lib/scylla/hints -type f -delete
sudo find /var/lib/scylla/view_hints -type f -delete

Login to one of the nodes in the cluster with (UN) status. Collect the following info from the node:
- cluster_name - cat /etc/scylla/scylla.yaml | grep cluster_name
- seeds - cat /etc/scylla/scylla.yaml | grep seeds:
- endpoint_snitch - cat /etc/scylla/scylla.yaml | grep endpoint_snitch
- Scylla version - scylla --version

Procedure¶

Note

If your Scylla version is earlier than Scylla Open Source 4.3 or Scylla Enterprise 2021.1, check if the dead node is a seed node by running cat /etc/scylla/scylla.yaml | grep seeds:.

If the dead node’s IP address is listed, the dead node is a seed node. Replace the seed node following the instructions in Replacing a Dead Seed Node.
If the dead node’s IP address is not listed, the dead node is not a seed node. Replace it according to the procedure below.

We recommend checking the seed nodes configuration of all nodes. Refer to Seed Nodes for details

Install Scylla on a new node, see Getting Started for further instructions. Follow the Scylla install procedure up to scylla.yaml configuration phase. Ensure that the Scylla version of the new node is identical to the other nodes in the cluster.
Note

Make sure to use the same Scylla patch release on the new/replaced node, to match the rest of the cluster. It is not recommended to add a new node with a different release to the cluster. For example, use the following for installing Scylla patch release (use your deployed version)
- Scylla Enterprise - sudo yum install scylla-enterprise-2018.1.9
- Scylla open source - sudo yum install scylla-3.0.3
In the scylla.yaml file edit the parameters listed below. The file can be found under /etc/scylla/.
- cluster_name - Set the selected cluster_name
- listen_address - IP address that Scylla uses to connect to other Scylla nodes in the cluster
- seeds - Set the seed nodes
- endpoint_snitch - Set the selected snitch
- rpc_address - Address for client connection (Thrift, CQL)
- consistent_cluster_management - set to the same value as used by your existing nodes.
Add the replace_node_first_boot parameter to the scylla.yaml config file on the new node. This line can be added to any place in the config file. After a successful node replacement, there is no need to remove it from the scylla.yaml file. (Note: The obsolete parameters “replace_address” and “replace_address_first_boot” are not supported and should not be used). The value of the replace_node_first_boot parameter should be the Host ID of the node to be replaced.

For example (using the Host ID of the failed node from above):

replace_node_first_boot: 675ed9f4-6564-6dbd-can8-43fddce952gy

Start Scylla node.

sudo systemctl start scylla-server
docker exec -it some-scylla supervisorctl start scylla
(with some-scylla container already running)

Verify that the node has been added to the cluster using nodetool status command.

For example:

Datacenter: DC1
Status=Up/Down
State=Normal/Leaving/Joining/Moving
--  Address        Load       Tokens  Owns (effective)                         Host ID         Rack
UN  192.168.1.201  112.82 KB  256     32.7%             8d5ed9f4-7764-4dbd-bad8-43fddce94b7c   B1
UN  192.168.1.202  91.11 KB   256     32.9%             125ed9f4-7777-1dbn-mac8-43fddce9123e   B1
DN  192.168.1.203  124.42 KB  256     32.6%             675ed9f4-6564-6dbd-can8-43fddce952gy   B1

192.168.1.203 is the dead node.

The replacing node 192.168.1.204 will be bootstrapping data. We will not see 192.168.1.204 in nodetool status during the bootstrap.

Use nodetool gossipinfo to see 192.168.1.204 is in NORMAL status.

/192.168.1.204
  generation:1553759984
  heartbeat:104
  HOST_ID:655ae64d-e3fb-45cc-9792-2b648b151b67
  STATUS:NORMAL
  RELEASE_VERSION:3.0.8
  X3:3
  X5:
  NET_VERSION:0
  DC:DC1
  X4:0
  SCHEMA:2790c24e-39ff-3c0a-bf1c-cd61895b6ea1
  RPC_ADDRESS:192.168.1.204
  X2:
  RACK:B1
  INTERNAL_IP:192.168.1.204

/192.168.1.203
  generation:1553759866
  heartbeat:2147483647
  HOST_ID:675ed9f4-6564-6dbd-can8-43fddce952gy
  STATUS:shutdown,true
  RELEASE_VERSION:3.0.8
  X3:3
  X5:0:18446744073709551615:1553759941343
  NET_VERSION:0
  DC:DC1
  X4:1
  SCHEMA:2790c24e-39ff-3c0a-bf1c-cd61895b6ea1
  RPC_ADDRESS:192.168.1.203
  RACK:B1
  LOAD:1.09776e+09
  INTERNAL_IP:192.168.1.203

After the bootstrapping is over, nodetool status will show:

Datacenter: DC1
Status=Up/Down
State=Normal/Leaving/Joining/Moving
--  Address        Load       Tokens  Owns (effective)                         Host ID         Rack
UN  192.168.1.201  112.82 KB  256     32.7%             8d5ed9f4-7764-4dbd-bad8-43fddce94b7c   B1
UN  192.168.1.202  91.11 KB   256     32.9%             125ed9f4-7777-1dbn-mac8-43fddce9123e   B1
UN  192.168.1.204  124.42 KB  256     32.6%             655ae64d-e3fb-45cc-9792-2b648b151b67   B1

Run the nodetool repair command on the node that was replaced to make sure that the data is synced with the other nodes in the cluster. You can use Scylla Manager to run the repair.

Note

When Repair Based Node Operations (RBNO) for replace is enabled, there is no need to rerun repair.

Handling Failures¶

If the new node starts and begins the replace operation but then fails in the middle e.g. due to a power loss, you can retry the replace (by restarting the node). If you don’t want to retry, or the node refuses to boot on subsequent attempts, consult the Handling Membership Change Failures document.

Setup RAID Following a Restart¶

In case you need to to restart (stop + start, not reboot) an instance with ephemeral storage, like EC2 i3, or i3en nodes, you should be aware that:

ephemeral volumes persist only for the life of the instance. When you stop, hibernate, or terminate an instance, the applications and data in its instance store volumes are erased. (see https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/storage-optimized-instances.html)

In this case, the node’s data will be cleaned after restart. To remedy this, you need to recreate the RAID again.

Stop the Scylla server on the node you restarted. The rest of the commands will run on this node as well.
sudo systemctl stop scylla-server
docker exec -it some-scylla supervisorctl stop scylla
(without stopping some-scylla container)
Run the following command, remembering not to mount an invalid RAID disk after reboot:
```
sudo sed -e '/.*scylla/s/^/#/g' -i /etc/fstab
```
Run the following command to replace the instance whose ephemeral volumes were erased (previously known by the Host ID of the node you are restarting) with the restarted instance. The restarted node will be assigned a new random Host ID.
```
echo 'replace_node_first_boot: 675ed9f4-6564-6dbd-can8-43fddce952gy' | sudo tee --append /etc/scylla/scylla.yaml
```

Run the following command to re-setup RAID

sudo /opt/scylladb/scylla-machine-image/scylla_create_devices

Start Scylla Server

sudo systemctl stop scylla-server

docker exec -it some-scylla supervisorctl stop scylla

(without stopping some-scylla container)

Sometimes the public/ private IP of instance is changed after restart. If so refer to the Replace Procedure above.

Was this page helpful?